- How To Install Disc Brake Anti Rattle Clips Brakes Rotors
- How To Install Disc Brake Anti Rattle Clips
- How To Install Disc Brake Anti Rattle Clips Brakes Install
Back to Top
Refurbish or Replace ?
Shop OEM Toyota Part # (0). Disc Brake Anti-Rattle Clip Set (Rear). Fitting Kit, Disc Brake. A set of clips, which snap onto the steering knuckle abutment or brake. Buy Bendix H5412DP Disc Brake Anti-Rattle Retainer Clip: Disc Hardware Kits. Front versus Rear Brakes. The installation method of Wotefusi Rear Brake System. Videos for related products. Click to play video. OEMTOOLS 27113 Disc Caliper Set, 18-Piece.
![Clips Clips](/uploads/1/1/8/6/118662282/270787562.jpg)
- I put on some 100 series brake pads and noticed that the anti-rattle clip was missing. Here is a video of the sound: I can hear it at any speed and it slows down/speeds up depending on how fast I am going. It is impossible to tell what area of the vehicle it is coming from.
- Step 13: Install Caliper Bracket & Brake Pads. Install the caliper bracket and torque the caliper bracket bolts to the manufacturer’s specifications. Then, install the new pads. Apply a small amount of brake lube on the back of the pads where they contact the caliper, as shown in the photo below.
![How to install anti rattle brake clips How to install anti rattle brake clips](/uploads/1/1/8/6/118662282/835009846.jpg)
What to do...what to do...? Should I use as much aspossible or build up from new? It all depends on the shape of the itemsyou came home from the salvage yard with. Rotors only cost 6 bucks to haveturned, but if they are factory originals and are close to their wear limits,then you're better off spending the extra $25 or so. Calipers can havefrozen pistons, or can leak if they've been on a junk car too long. Thecost of rebuilding them yourself is about $8 less than getting fresh ones fromthe store. Flex brake lines can rot and crack, but may still begood. It's always wise to remove and replace the inner and outer bearings.
Back to Top
How To Install Disc Brake Anti Rattle Clips Brakes Rotors
Installation
How To Install Disc Brake Anti Rattle Clips
Rule of the day: SAFETY!You are working with a 'safety of flight item' for your car. It ismandatory that this be done correctly and safely. You will be putting yourselfat risk by working under the car. You will be driving at high speeds andwill have passengers in your car, as well as ME in the oncoming trafficlane. Do not attempt this if you are not completely comfortable in yourknowledge of vehicle maintenance. I ASSUME NO RESPONSIBILITY FOR WHAT ISPROVIDED HERE. THIS SITE IS FOR INFORMATION PURPOSES ONLY. DO THIS MOD ATYOUR OWN RISK! (Have I left out any other disclaimers?) All kidding aside, thisis not swapping headlights or steering wheels....this is SERIOUS SAFETYstuff.
How To Install Disc Brake Anti Rattle Clips Brakes Install
- Jack up the car and remove wheels. Disconnect flex brake lines at the hard line joint. Pull shock absorber, then remove, or compress the front spring using a spring compressor. BE EXTREMELY CAREFUL.
- Remove existing drum system at the spindle joint to the upper and lower ball joints, and the tie rod.
- Be sure to measure the total length of the tie rod assembly; you will be aiming to install the new tie rod at about the same length. Remove the existing tie rod as it will not fit the Granada spindle.
- Disconnect the Master cylinder at the brake pedal attach pin, remove the push rod.
- Disconnect the brake lines from the existing distribution block. Cap remaining connections of lines going to the front and rear..
- Remove the two screws holding the single master cylinder, and the one screw holding the distribution block to the apron. Remove as an assembly.
- To install the spindle, the upper and lower arms need to be free to move up and down. This is why the front shocks and springs need to be removed, or the spring at least pulled up and secured. Use tons of caution when working with the spring. Buy or rent a good spring compressor. Don't skimp here.
- All replaced parts need to be Torqued per the torque values in the Mustang Shop manual.
- Here are the values for the 1966 unit